mdp 01, 03, 05 www.vishay.com vishay dale revision: 12-sep-13 1 document number: 31511 for technical questions, contact: ff2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 thick film resistor networks, dual-in-line, molded dip features ? isolated, bussed, and dual terminator schematics available ? 0.160" (4.06 mm) maximum seated height and rugged, molded case construction ? thick film resistive elements ? low temperature coefficient (-55 c to +125 c) ? 100 ppm/c ? reduces total assembly costs ? compatible with automa tic inserting equipment ? wide resistance range (10 ? to 2.2 m ? ) ? uniform performance characteristics ? available in tube pack ? material categorization: for defi nitions of compliance please see www.vishay.com/doc?99912 note ? * this datasheet provides information abou t parts that are rohs-compliant and/ or parts that are non-rohs-compliant. for example, parts ? with lead (pb) terminations are not ro hs-compliant. please see the information/ tables in this datasheet for details. notes (1) for resistor power ratings at +25 c see derating curves (2) tighter tracking available (3) 2 % standard, 1 %, and 5 % available note ? for additional information on packaging, refer to the through-hole network packaging document ( www.vishay.com/doc?31542 ). available available standard electrical specifications global ? model/ ? no. of ? pins schematic power rating element (1) p 70 c w resistance range ? tolerance (3) % temperature coefficient (-55 c to +125 c) ppm/c tcr tracking (2) (-55 c to +125 c) ppm/c weight g mdp 14 01 0.125 10 to 2.2m 1, 2, 5 100 50 1.3 03 0.250 10 to 2.2m 50 05 0.125 consult factory 100 mdp 16 01 0.125 10 to 2.2m 1, 2, 5 100 50 1.5 03 0.250 10 to 2.2m 50 05 0.125 consult factory 100 global part number information new global part numbering: mdp1403100rg d04 (preferred part numbering format) global model pin count schematic resistance value tolerance code packaging special mdp 14 = 14 pin 16 = 16 pin 01 = bussed 03 = isolated 00 = special r = ? k = k ? m = m ? 10r0 = 10 ? 680k = 680 k ? 1m00 = 1.0 m ? 0000 = 0 ? jumper f = 1 % g = 2 % j = 5 % s = special z = 0 ? jumper e04 = lead (pb)-free, tube blank = standard (dash number) (up to 3 digits) from 1 to 999 as applicable d04 = tin/lead, tube historical part number example: mdp 1403101g (will continue to be accepted) mdp 14 03 101 g d04 historical model pin count schematic resistance value tolerance code packaging new global part numbering: mdp1405121cgd 04 (preferred part numbering format) global model pin count schematic resistance value tolerance code packaging special mdp 14 = 14 pin 16 = 16 pin 05 = dual terminator 3 digit impedance code, followed by alpha modifier (see impedance codes table) f = 1 % g = 2 % j = 5 % e04 = lead (pb)-free, tube blank = standard (dash number) (up to 3 digits) from 1 to 999 as applicable d04 = tin/lead, tube historical part number example: mdp 1405221271g (will continue to be accepted) mdp 14 05 221 271 g d04 historical model pin count schematic resistance value 1 resistance value 2 tolerance code packaging 4 0 d g r 0 0 1 3 0 4 1 p d m 4 0 d g c 1 2 1 5 0 4 1 p d m
mdp 01, 03, 05 www.vishay.com vishay dale revision: 12-sep-13 2 document number: 31511 for technical questions, contact: ff2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dimensions in inches (millimeters) note ? for additional impedanc e codes, refer to the dual terminat or impedance code table document ( www.vishay.com/doc?31530 ). global model a b c mdp 14 0.750 (19.05) 0.600 (15.24) 6 mdp 16 0.850 (21.59) 0.700 (17.78) 7 technical specifications parameter unit mdp14 mdp16 package power rating (max imum at +70 c) w 1.73 1.92 voltage coefficient of resistance v eff < 50 ppm typical dielectric strength v ac 200 insulation resistance ? > 10 000m minimum operating temperature range c -55 to +125 storage temperature range c -55 to +150 mechanical specifications marking resistance to solvents permanen cy testing per mil- std-202, method 215 solderability per mil-std-202, method 208e body molded epoxy terminals solder plated leads weight 14 pin = 1.3 g; 16 pin = 1.5 g impedance codes code r 1 ( ? ) r 2 ( ? )code r 1 ( ? ) r 2 ( ? ) 500b 82 130 141a 270 270 750b 120 200 181a 330 390 800c 130 210 191a 330 470 990a 160 260 221b 330 680 101c 180 240 281b 560 560 111c 180 270 381b 560 1.2k 121b 180 390 501c 620 2.7k 121c 220 270 102a 1.5k 3.3k 131a 220 330 202b 3k 6.2k 0.010 + 0.005 - 0.002 (0.254 + 0.127 - 0.051) 0.250 0.005 (6.35 0.127) 0.310 0.010 (7.87 0.254) 0.290 min. 0.320 nom. 0.360 max. (7.37 min. 8.13 nom. 9.14 max.) pin #1 non-accumulative tol. "c" spaces a 0.010 (0.254) 0.030 (0.762) typ. 0.100 0.010 (2.54 0.254) 0.075 0.015 (1.90 0.381) 0.120 0.005 (3.05 0.127) 0.130 + 0.015 - 0.010 (3.30 + 0.381 - 0.254) 0.050 0.005 (1.27 0.127) 0.018 0.003 (0.457 0.076) b 0.010 (0.254) pin #1 identification
mdp 01, 03, 05 www.vishay.com vishay dale revision: 12-sep-13 3 document number: 31511 for technical questions, contact: ff2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? standard e24 resistance values stocked. consult factory. derating circuit applications 01 schematic 13 and 15 resistors wi th one pin common the mdpxx01 circuit provides a ch oice of 13 and 15 nominally equal resistors, each connect ed between a common pin (14 and 16) and a discrete pc board pin. commonly used in the following applications: ? mos/rom pull-up/pull-down ? ? open collector pull-up ? ? wired or pull-up ? ? power driven pull-up ? ? ttl input pull-down ? digital pulse squaring ? ttl unused gate pull-up ? high speed parallel pull-up ? 03 schematic 7 or 8 isolated resistors the mdpxx03 provides a choice of 7 and 8 nominally equal resistors, each resistor isolated from all others and wired directly across. commonly used in the following applications: ? wired or pull-up ? power driven pull-up ? ? powergate pull-up ? ? line termination ? ? long-line impedance balancing ? led current limiting ? ecl output pull-down ? ttl input pull-down ? 05 schematic ttl dual-line terminator; pulse squaring the mdpxx05 circuit contains 12 and 14 series pair of resistors. each series pair is connected betwee n ground and a common line. the junction of these resistor pairs is connected to the in put terminals. the 05 circuits are designed for ttl dual-line termination and pulse squaring. ? ? ? ? ? ? ? ? ? ? pin #1 mdp1401 mdp1601 mdp1603 mdp1403 pin #1 mdp1405, mdp1605 pin #1 r1 r1 r1 r1 r1 r1 r1 r2 r2 r2 r2 r2 r2 r2 r1 r1 r1 r1 r1 r1 r1 r2 r2 r2 r2 r2 r2 r2 16 pin package 14 pin package single resistor 03 01 and 05 3.00 2.70 0.380 0.190 - 50 + 25 + 70 + 125 + 150 ambient temperature c power rating (w)
mdp 01, 03, 05 www.vishay.com vishay dale revision: 12-sep-13 4 document number: 31511 for technical questions, contact: ff2aresistors@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 performance test conditions max. ? r (typical test lots) power conditioning 1.5 rated power, applied 1.5 h on and 0.5 h off for 100 h 4 h at +25 c ambient temperature 0.50 % ? r thermal shock 5 cycles betwee n -65 c and +125 c 0.50 % ? r short time overload 2.5 x rate d working voltage 5 s 0.25 % ? r low temperature operation 45 min at full rated working voltage at -65 c 0.25 % ? r moisture resistance 240 h wi th humidity ranging from 80 % rh to 98 % rh 0.50 % ? r resistance to soldering heat leads immersed in +350 c solder to with in 1/16" of device body for 3 s 0.25 % ? r shock total of 18 shocks at 100 g s 0.25 % ? r vibration 12 h at maximum of 20 g s between 10 hz and 2000 hz 0.25 % ? r load life 1000 h at +70 c, rated power applied 1.5 h on, 0.5 h off for full 100 0 h period. derated according to the curve. 1.00 % ? r terminal strength 4.5 pound pull for 30 s 0.25 % ? r insulation resistance 10 000 m ? (minimum) - dielectric withstanding voltage no evid ence of arcing or damage (200 v rms for 1 min) -
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
